The F-4TEL is used for carrying four phone lines over fiber optic cable. Telephone over Fiber applications offer a secure connection that is impossible to bug. The PSTN two-wire POTS telephone port can be configured either as an FXO (PBX trunk) or FXS (telephone set/fax machine/dial-up modem) device just by a simple DIP switch setting. Using a pair of these devices, four independent telephone lines can be extended over a fiber link. The F-4TEL provides full service for features like caller ID. The converter can be used in service mode, allowing connection of 2 telephone sets. The unit offers SNMP allowing remote management and sensing of converter status, type, version, fiber link status, RJ11 port status, and alarms. The F-4TEL is a simple and reliable solution for data carriers and service providers for Telephone over Fiber links.
• Extend telephone voice transmission from 2km to 120km over fiber
• Network management via terminal, web or SNMP
• Supports telephone voice transmission
• Supports caller ID pass-through
• The Tx Transmitter) connects to FXS (telephone set/fax machine/dial-up modem)
• The RX (receiver) connects to FXO - ( (PBX trunk)
| Model Number | Description |
|
4 CH Telephone FXO/FXS Singlemode Fiber Transmitter and Reciever for 20km • The Tx Transmitter) connects to FXS (telephone set/fax machine/dial-up modem) • The RX (receiver) connects to FXO - ( (PBX trunk) |
|
4 CH Telephone FXO/FXS Multimode Fiber Transmitter and Receiver kit for 2km (please call 800-521-8467 ext 1) |
|
4 CH Telephone FXO/FXS Singlemode Fiber Transmitter for 40km (please call 800-521-8467 ext 1) |
|
4 CH Telephone FXO/FXS Singlemode Fiber Transmitter and Receiver kit for 80km (please call 800-521-8467 ext 1) |
|
4 CH Telephone FXO/FXS Singlemode Fiber Transmitter and receiver kit for 120km (please call 800-521-8467 ext 1) |
| *All Specifiactions Subject to Change Without Notice | |||
| Optical Interface: | |||
|
ST/PC | ||
|
MM 2km, SM 15/30/50/80/120km, WDM 20/40/60/80km | ||
|
MM 1310nm, SM 1310, 1550nm, WDM 1310Tx/1550Rx, 1550Tx/1310Rx | ||
| Electrical Interface | |||
|
RJ-11 | ||
|
600 ohms, Coding : 16 bits liner, Loop Current : 10~100mA Ring Frequency : Acceptable 20 ~50Hz, Insertion Loss: 0.0 ± 1.0dB at 1000H |
||
|
Impedance : 600 ohms, Coding : 16 bits liner, Dial: DTMF and Dial Pulse, Battery Source: 48VDC ± 4 |
||
|
Sine Wave | ||
|
20/25/30/50 Hz selectable | ||
|
FXS to FXS : On / 1 sec, Off / 2 sec | ||
|
Reproduces the cadence detected by FXO Insertion Loss 0.0 ± 1.0dB at 1000Hz REN: 4.0B(Ring Equivalence Number |
||
|
Power, FX Link, Phone Act, Test | ||
|
DC IN 12V | ||
|
5 W | ||
|
480mm x 225mm x 44mm | ||
|
0~50°C (Operating) 0~70°C (Storage) |
||
|
CE, FCC, LVD, RoHS | ||
|
125,000 h (25°C) | ||
Unfortunately, that is not possible because of the multiplexing
the technology they utilize.
Because those units require bidirectional communication, they are sold
in sets; since they are sold in sets you can not mix and match them.
Since they are bidirectional units you can't use them with a
correlating splitter either.
So essentially you need to put a transmitter and receiver in every
the location that you require them in.
If you have 8 locations, you could use 8 F-1TEL-TX/RX kits or 8
F-2TEL-TX/TX kits
https://thorbroadcast.com/product/1-or-2-telephone-line-over-fiber.html
16 Analog Telephone Lines over Fiber transceiver
Extend independent 16 phones over 1 fiber optic cable. 16 Channel telephones over fiber transceiver for secure telephone lines. These units transport the standard analog phone signal point to point over fiber optic cable and are impossible to tap.
10/100/1000 Mbps Fast and Gigabit Ethernet Over 1 Fiber Media Converter Kit
Bi-directional 10/100/1000 Fast and Gigabit Ethernet Transport over one fiber; the Converter has 1 single fiber optic connector for transmitting at 1310nm and receiving at 1550nm, and 10/100/1000Base-TX to 1000Base-FX Fast and Gigabit Ethernet copper RJ45 fo fiber Converter SC/UPC,The Link contain both units A and B side + power supplies
ES
