The F-KuBAND is used to transmit and receive uplink and down link signals up to 15 GHz. This is useful for links in between control rooms or NOCs. The F-KuBAND system offers a high performance alternative to conventional coaxial link systems, both reducing attenuation and eliminating the need for a waveguide. The unit functions as a transparent link, transporting all satellite modulation formats over a single fiber. Typically a Ku-Band fiber link consists of an optical transmitter that receives the RF signal and transmits it over single mode fiber to an optical receiver which converts the optical signal back to RF. When used in CWDM configurations the F-KuBAND is able to transmit up to 8 independent satellite signals over a single fiber. The F-KuBAND link is a cost effective and high performance solution for KU-Band over fiber Satellite links.
• Useful Bandwidth up to 15 GHz
• Ku Band Over Fiber for links up to 120 km
• Highly Linear for Analog Transmission
• Low RIN, Narrow Linewidth DFB Laser
• Broadband LiNbO3 Modulator
• Linear PIN reciever with TIA
• Optional single port design allows Bi-directional Transmission with 1 fiber
• Optional RF amplifier to enhance gain
IMPORTANT NOTE*** (it is very important to interface our unit with SC/APC - Angle Polished Connector to avoid any light reflections.
If your fiber is terminated with the SC, ST, FC /PC flat connector, you need to use an optical jumper from PC type to SC/APC for proper conversion.
|
Model Number |
Description |
|
Ku-BAND Singlemode Fiber Transmitter for 10km |
|
Ku-BAND Singlemode Fiber Reciever for 10km |
|
Ku-BAND Singlemode Fiber Transmitter for 40km |
|
Ku-BAND Singlemode Fiber Reciever for 40km |
|
Ku-BAND Singlemode Fiber Transmitter for 80km |
|
Ku-BAND Singlemode Fiber Reciever for 80km |
|
Ku-BAND Singlemode Fiber Transmitter for 120km |
|
Ku-BAND Singlemode Fiber Reciever for 120km |
|
*All Specifiactions Subject to Change Without Notice IMPORTANT NOTE*** (it is very important to interface our unit with SC/APC - Angle Polished Connector to avoid any light reflections. If your fiber is terminated with the SC, ST, FC /PC flat connector, you need to use an optical jumper from PC type to SC/APC for proper conversion. |
|||
|
10.0 - 15.0 GHz |
||
|
>70 dB |
||
|
± 0.2 dB / 48 MHz |
||
|
-50 dBc (max.), -55 dBc (typ.) |
||
|
(36 MHz BW) >50 dBc |
||
|
Input Signal |
|
||
|
-25 to -40 dBm |
||
|
-10 to -40 dBm |
||
|
± 0.15 dB / 24 hours |
||
|
|
||
|
-15 to 0 dBm (typ.) |
||
|
0 to +15 dBm (typ.) |
||
|
Noise Figure @ max input gain |
|
||
|
<22 dB (typ.) |
||
|
<9 dB (typ.) |
||
|
Peak to peak 0.4 ns (typ.) |
||
|
50 Ohm |
||
|
1.4:1 |
||
|
Maximum RF Input (with no damage) |
|
||
|
-10 dBm |
||
|
+5 dBm |
||
|
standard |
||
|
20 dB ± 1.0 |
||
4 GPS signals over the Fiber TX/RX with Outdoor Waterproof Enclosure
4 GPS RF carrier signals over 4 fiber Outdoor waterproof enclosure optical Transmitter and 19" rack-mountable Receiver with redundant power supply
GPS over Fiber - Reference Timing Fiber Optic Waterproof Solution
Waterproof Outdoor GPS fiber optic Transmitter and 19" rack-mountable receiver, sends the signal from a GPS antenna to a receiver over singlemode fiber. The transmitter and receiver has RF and Optical meters, allows quick and seemless implementation without any Optical and RF instruments.
ES
