Modulators are used in telecommunications to send information. In order to transmit information from the transmitter to the receiver, the carrier wave (high frequency signal in a given band) must be modulated with information (e.g. voice, data, low frequency modulation signal, ) with a different frequency. Depending on the type of modulation, the modulator must change the appropriate information size in a given cycle.
Example from practice: An FM radio station (e.g. 100 MHz) generates a carrier wave with an average frequency of 100 MHz, but changes (modulates) its frequency in time using a low frequency signal (voice, music). This can be done, for example, by means of a capacitive diode in the resonant circuit of a high-frequency oscillator to which a low-frequency signal is applied. In this way, its capacity in the LF signal cycle, and thus the resonance frequency of the resonant circuit, changes.
HDMI digital modulator works exactly as described above, using a digital signal which is practically used in all popular applications, instead of an analog signal. The HDMI connectors themselves are a modern and practical solution applied in most of the modulators nowadays.
Digital modulator for HD video distribution over coax - QAM, ATSC, DVB-T. Broadcast to unlimited TVs with FULL HD live HDMI video as Cable TV & IPTV channels
Features
Integrates fully independent encoders with a multiplexer and modulator
Modulates up to 4 adjacent QAM-256 carriers with up to 38 Mbps each
Supports full HD 1080p60 input & encoding from any HDMI digital video source
Each encoder independently configured: supports all standard HDTV resolutions
IPTV output on second network port in UDP IGMP Multicast or Unicast format
DVB-ASI output on mirrored BNC terminals for use in broadcasting systems
Fully network managed device with all settings configurable through web browser
Conversions : HDMI to RF, HDMI to IP, HDMI to ASI
Any 1-4 HDMI Input up to 720p/1080i/1080p60
Licensed HDMI inputs
1-4 CATV RF Output up to 4 Adjacent channels
QAM-256/64
Fully IP control and Network Management through browser
Front Panel LCD local control
IPTV Output Unicast or Multicast IGMP UDP, RTP/RTSP
ASI Output with multiplexer cherry picking
Low Latency available 300/500/800ms delay via different modes - IP will always be closer to 800ms due to the decoding (these values are end to end, not just the encoding speed)
AC3 Audio available (AC3 model)
MPEG2 Video or MPEG4 H.264 Encoding
Firmware for ATSC, DVB-T, DVB-S2 Available
2 slot design – Other Video Inputs cards available –Hot swappable - SDI Card, YpbPr Card.
IPTV Output Unicast or Multicast IGMP UDP, RTP/RTSP
ASI Output with multiplexer cherry picking
Any HDMI Input up to 1.5A @1080p60
ASI Input SPTS or MPTS up to 120 Mbps
Fully Network Managed through browser
Integrates fully independent encoders with a multiplexer and modulator
Modulates up to 4 adjacent 8VSB carriers compatible with ATSC format
Supports full HD 1080p60 input & encoding from any HDMI digital video source
Each encoder independently configured: supports all standard HDTV resolutions
IPTV output on second network port in UDP IGMP Multicast or Unicast format
DVB-ASI output on mirrored BNC terminals for use in broadcasting systems
Fully network managed device with all settings configurable through web browser
300/500/800ms delay via different modes - IP will always be closer to 800ms due to the decoding (these values are end to end, not just the encoding speed)
Convert HD video signals to full HD digital DVB-T television channels for display on any TV. Broadcast over your existing Coaxial Cabling to an unlimited number of Televisions with FULL HD
Features
Conversions : HDMI to RF DVB-T , HDMI to IP, HDMI to ASI
Any 1-4 HDMI Input up to 720p/1080i/1080p60
Licensed HDMI inputs
1-4 CATV RF Output up to 4 Adjacent channels
QPSK QAM-16/26 RF Out up to 4 Adjacent
Fully IP control and Network Management through browser
Front Panel LCD local control
IPTV Output Unicast or Multicast IGMP UDP,RTP/RTSP
ASI Output with multiplexer cherry picking
Low Latency available Low Latency available 300/500/800ms delay via different modes - IP will always be closer to 800ms due to the decoding (these values are end to end, not just the encoding speed)
AC3 Audio available (AC3 model)
MPEG2 Video or MPEG4 H.264 Encoding
Firmware for ATSC, DVB-T, DVB-S2 Available
2 slot design – Other Video Inputs cards available –Hot swappable - SDI Card, YpbPr Card.
5 Years warranty
Any HDMI Input up to Full HD @1080p60
ASI Input SPTS or MPTS up to 120 Mbps
Integrates fully independent encoders with a multiplexer and modulator
Modulates up to 4 adjacent QPSK, QAM-16/64 carriers with up to 28 Mbps each
Supports full HD 1080p60 input & encoding from any HDMI digital video source
Each encoder independently configured: supports all standard HDTV resolutions
IPTV output on second network port in UDP IGMP Multicast or Unicast format
DVB-ASI output on mirrored BNC terminals for use in broadcasting systems
Fully network managed device with all settings configurable through web browser
Support CC (Closed Caption) EIA608 (from CVBS input)
1-4 CATV RF Output up to 4 Adjacent channels
QAM-256/64, DVB-T & ATSC formats available
Fully IP Control and Network Management through browser
Front Panel LCD local control
IPTV Output Unicast or Multicast IGMP UDP, RTP / RTSP
ASI Output multiplexer with cherry picking
Low Latency available 300/500/800ms delay via different modes - IP will always be closer to 800ms due to the decoding (these values are end to end, not just the encoding speed)
Dolby AC3 or MPEG1/2 Audio Encoding
MPEG2 or MPEG4 H.264 Video Encoding
Firmware for ATSC, DVB-T, DVB-S2 Available
VCT (Virtual Channel Table) support for DVB-C and ATSC
This unit converts 4 RF Satellite/ATSC/QAM or ASI to QAM. Transmodulator: ATSC to QAM, CATV RF, QAM to ATSC, QAM, Satellite RF to QAM, Satellite to ATSC, Satellite to QAM.
Features
Modulate 4 RF carriers including all sub programs and streams
Provides industry standard multiplexed and remapped outputs on ASI & IP
9x IP stream outputs (8 SPTS, 1 MPTS) in UDP, RTP, or RTSP video protocols
Advanced network managment system on dedicated network port and IP address
Modulator available in QAM (DVB-C), Satellite (DVB-S2) or OTA (DVB-T) -- (model dependant)
Supports Closed Caption 608 and 708 systems, supports Dolby AC/3 Pass Through
H-4-DVBS2-QAM 4 satellite LNB’s RF + 2 ASI’s to QAM and IP
This unit has 2 HDMI and 2 SDI inputs with RF CATV QAM and ATSC output. You can broadcast over existing coaxial cabling to an unlimited number of televisions in FULL HD
Features
Convert 2 HDMI & 2 SDI HD Video Content programs to Perfect QAM Channels simultaneously
Any 2 HDMI & 2 SDI Inputs up to 720p/1080i/1080p
Licensed HDMI inputs
2 HDMI and 2 BNC cables FREE
Support DD AC3 (2.0/5.1/7.1) passthrough(for HDMI interface only)
Support CC (Closed Caption) EIA608,and EIA708 on SDI’s
1-4 CATV RF Output up to 4 Adjacent channels
QAM-256/64, DVB-T, & ATSC formats available
Fully IP control and Network Management through browser
Front Panel LCD local control
IPTV Output Unicast or Multicast IGMP UDP/RTP/RTSP
ASI Output with multiplexer cherry picking
Low Latency available 300/500/800ms delay via different modes - IP will always be closer to 800ms due to the decoding (these values are end to end, not just the encoding speed)
Dolby AC3 Audio encoding and Doby AC3, 5.1 Pass-Trough
MPEG2 Video or MPEG4 H.264 Encoding
Firmware for DVB-C, ATSC, DVB-T, DVB-S2, ISDB-T Available
VCT (Virtual Channel Table) support—for DVB-C ATSC and DVB-T
Modern modulators have many advantages for distributing a signal directly. You can transmit both analog and digital signals in this way. The proper choice of unit is optimally adjusted to your requirements may be sometimes difficult. That's why it pays to choose Thor Broadcast solutions. In case of any even small question you can just ask and get an instant answer. An optimal combination of audio-video equipment is too important to leave room for error.
EN
